Search
- New Products, Part 2
- (Magazine)
- May 30, 2005, ... low-temperature thermal cracking in the absence of air and utilizes the output to produce electricity. System includes feeding unit, reaction unit, distillation unit, sludge extractor/drying unit, circulation ...
- A Communication from the PLACE Div. of TAPPI
- (Magazine)
- May 30, 2005, ... Imaging For Extruder Analysis And Improvement by Andrew W. Christie, Optex Process Solutions, LLC Recently, improved infra-red temperature sensing tools have become readily available to provide a more ...
- Truth or Myth?
- (Magazine)
- May 30, 2005, ... Truth or Myth? Some packagers believe ambient conditions, especially temperature and humidity, might affect slide angle during testing or throughout processing. Truth. We tested several samples under ...
- Detecting the Edge
- (Magazine)
- March 30, 2005, ... temperature swings—but they were a big improvement over their predecessors Web Guides Web guides have evolved dramatically since their first appearance on converting lines in the 1930s. The earliest ...
- Hot Melt Adhesive Use
- (Magazine)
- February 27, 2005, ... they are the adhesive of choice. By some measurements, hot melts are among the fastest growing adhesives in the industry. Hot melt adhesive application temperature is perhaps the most important variable ...
- A Communication from the PLACE div. of TAPPI
- (Flexpack)
- December 30, 2004, ... min and densities of 918 to 920 kg/m3. The melt temperature was monitored to 295–305°C by means of an infrared camera. In principle, the methodology was as follows. Extruder screw rpm was set to give 10 ...
- Getting it Right, the First Time
- (Magazine)
- December 30, 2004, ... you run certain types of plastic, perhaps at a certain temperature?" The software even allows paper mills to send a converter a record of defects to help slitter or rewinder operators plan ahead. Scott ...
- New Product Digest, Part 1
- (Magazine)
- November 29, 2004, New products from: Rotatek, HCI Converting Equipment Co., Maguire Products, Sterling Toggle, Battenfeld Gloucester Engineering, NexGen Enviro Systems, Pinnacle Converting Equipment, Davis-Standard, Agfa, ...
- PFFC Worldwide Special Report on Release Liners, part 2
- (Archive)
- October 30, 2004, ... and crosslinkers with proprietary architectures, plus a choice of release modifiers and catalysts. Two inhibitor choices meet differing needs for low-temperature cure vs. longer thin-film bath stability. ...
- Products, Part 1
- (Magazine)
- September 29, 2004, ... High-accuracy analog ultrasonic sensor has a range of ±0.002 in. or 0.05% of range, whichever is greater, at 25 deg C. Features a built-in temperature target that monitors and compensates for air temperature ...
- New Clear Barrier Film Resin Technology Replaces Coated Films
- (Archive)
- September 29, 2004, Creating packaging that allows consumers to see clearly the food they are purchasing — and also promises the food is fresh — presents converters and end-users with a unique manufacturing challenge. ...
- Weight Control
- (Magazine)
- June 29, 2004, ... that controls the coating weight. In these processes, the viscosity can change due to evaporation of solvent, change in percent solids, reaction of ingredients, temperature, or the incorporation of bubbles. ...
- Binary Blends of EVA and Metallocene Catalyzed Ethylene-a-Olefin Copolymers & Their Film Properties
- (Magazine)
- June 29, 2004, ... available 43-mm. co-rotating, twin-screw extruder with a length to diameter ratio of 40:1 equipped with a pelletizer. The extruder ran at 150 rpm with an output rate of 18 kg/h. The extrusion temperatures ...
- A Recipe for Flexo Printing Success
- (Flexpack)
- May 30, 2004, ... and rewind areas. Each job uses different substrates, and it is important to know what tension will allow the web to float through the press without distorting its dimensions. Temperature—In a wide web, ...
- How to Influence Gloss and Friction Coatings or Cast Films by the Chill Roll Surface Design
- (The Place)
- May 30, 2004, ... of a chill roll. Besides this texture, other important factors are production speed, temperature, line pressure, support material, and coating material. All these parameters must correlate with each other. ...
- Using a Chemical Primer for High Bonds & Low Oxygen Transmission
- (Magazine)
- April 30, 2004, ... coating requires thorough drying. Residual moisture will compromise the adhesion to the substrate and oxygen barrier performance. Variables including line speed, oven temperature, web temperature, oven ...
- Products
- (Magazine)
- April 29, 2004, ... New transducer design is stable, even at low tensions, and maintains exact measurements regardless of ambient temperature changes, company adds. Eliminate Static without Power TAKK Industries, Cincinnati, ...
- Products
- (Magazine)
- February 29, 2004, ... Accessories, Services Pyrometer Includes TV Camera Mikron Infrared, Oakland, NJ; 201/405-0900; mikroninfrared.com Model MI-GA5-TV digital pyrometer is for noncontact temperature measurement between ...
- Migration of Fluorescent Whitening Agents from Food Packaging Made from Recycled Paper
- (Magazine)
- February 28, 2004, ... and fatty foods, respectively. Extractions were conducted at 20°C and 66°C for 30 minutes to represent short-term contact of the paper with foods under room temperature and hot-fill conditions. Test results ...
- G Prime A Rheological Indicator to Predict the Extrusion Coating Performance of LDPE
- (The Place)
- January 31, 2004, ... on a pilot extrusion coating line. All grades had melt flow range (MFR) between 7 and 9 g/10 min. and densities of 918-920 kg/m3. The melt temperature was monitored to 305∞C by means of an infrared camera. ...